Home

KWH20G HANDLE + POMMEL

20 cm carbon crank with pommel. This is a crank with a 100% carbon body, top-of-the-range grip bearings with very low friction, and a simple and ergonomic locking system.

20 cm carbon crank with pommel. This is a crank with a 100% carbon body, top-of-the-range grip bearings with very low friction, and a simple and ergonomic locking system.

KWH25 HANDLE + POMMEL

25 cm carbon crank with pommel.  This is a crank with a 100% carbon body, top-of-the-range grip bearings with very low friction, and a simple and ergonomic locking system.

25 cm carbon crank with pommel.  This is a crank with a 100% carbon body, top-of-the-range grip bearings with very low friction, and a simple and ergonomic locking system.

LINK PLATE KRS40 MEDIUM

Extension link for KRS40 genoa furling system. The lower end is mounted to the deck (hole diameter: 12 mm). The upper end is connected to the KRS40 furling drum Link length: 240 mm.

Extension link for KRS40 genoa furling system. The lower end is mounted to the deck (hole diameter: 12 mm). The upper end is connected to the KRS40 furling drum Link length: 240 mm.

OPTIONAL 2:1 BLOCK KF8.0...

PIN KRS Ø14 - M12...

14 mm pin for KRS30 and KRS40. Each KRS is delivered with a pin on which the bottom eye end of the forestay is attached. The standard pin is statistically the one that is used the most but in around 30% of cases, the pin must be replaced by a version with a larger or smaller diameter.

14 mm pin for KRS30 and KRS40. Each KRS is delivered with a pin on which the bottom eye end of the forestay is attached. The standard pin is statistically the one that is used the most but in around 30% of cases, the pin must be replaced by a version with a larger or smaller diameter.

PIN KRS Ø16 - M12...

16 mm pin for KRS30 and KRS40. Each KRS is delivered with a pin on which the bottom eye end of the forestay is attached. The standard pin is statistically the one that is used the most but in around 30% of cases, the pin must be replaced by a version with a larger or smaller diameter.

16 mm pin for KRS30 and KRS40. Each KRS is delivered with a pin on which the bottom eye end of the forestay is attached. The standard pin is statistically the one that is used the most but in around 30% of cases, the pin must be replaced by a version with a larger or smaller diameter.

PIN KRS Ø18 - M12...

18 mm pin for KRS30 and KRS40. Each KRS is delivered with a pin on which the bottom eye end of the forestay is attached. The standard pin is statistically the one that is used the most but in around 30% of cases, the pin must be replaced by a version with a larger or smaller diameter.

18 mm pin for KRS30 and KRS40. Each KRS is delivered with a pin on which the bottom eye end of the forestay is attached. The standard pin is statistically the one that is used the most but in around 30% of cases, the pin must be replaced by a version with a larger or smaller diameter.

SPARE LOCK FOR KF1.5 TO...

Lock replacement for KF1.5 and KF3.0 furlers All our furlers, from KF1.5 to KF12.0, are equipped with an automatic drum locking system that can be operated remotely. This function relies on two components: a concealed guide track and a removable lock that can be detached without tools.

Lock replacement for KF1.5 and KF3.0 furlers All our furlers, from KF1.5 to KF12.0, are equipped with an automatic drum locking system that can be operated remotely. This function relies on two components: a concealed guide track and a removable lock that can be detached without tools.

SPARE LOCK FOR KF3.0 LARGE...

Lock replacement for KF3 Large and KF12.00 furlers All our furlers, from KF1.5 Large to KF12.0, are equipped with an automatic drum locking system that can be operated remotely. This function relies on two components: a concealed guide track and a removable lock that can be detached without tools.

Lock replacement for KF3 Large and KF12.00 furlers All our furlers, from KF1.5 Large to KF12.0, are equipped with an automatic drum locking system that can be operated remotely. This function relies on two components: a concealed guide track and a removable lock that can be detached without tools.

ALUMINUM THIMBLE FOR KF1.5...

Aluminum thimble for KF1.5, KTS1.5 and KFH1.5 The thimble is the link between the anti-torsion of the sail and the furler. It is an anodized aluminum part that adapts perfectly to the forks of our furlers.

Aluminum thimble for KF1.5, KTS1.5 and KFH1.5 The thimble is the link between the anti-torsion of the sail and the furler. It is an anodized aluminum part that adapts perfectly to the forks of our furlers.

ALUMINUM THIMBLE FOR KF3.0...

Aluminum thimble for KF3.0, KTS3.0 and KFH3.0 The thimble is the link between the anti-torsion of the sail and the furler. It is an anodized aluminum part that adapts perfectly to the forks of our furlers.

Aluminum thimble for KF3.0, KTS3.0 and KFH3.0 The thimble is the link between the anti-torsion of the sail and the furler. It is an anodized aluminum part that adapts perfectly to the forks of our furlers.

ALUMINUM THIMBLE FOR KF4.5...

Aluminum thimble for KF4.5, KTS4.5 and KFH4.5 The thimble is the link between the anti-torsion of the sail and the furler. It is an anodized aluminum part that adapts perfectly to the forks of our furlers.

Aluminum thimble for KF4.5, KTS4.5 and KFH4.5 The thimble is the link between the anti-torsion of the sail and the furler. It is an anodized aluminum part that adapts perfectly to the forks of our furlers.

ALUMINUM THIMBLE FOR KF6.0...

Aluminum thimble for KF6.0, KTS6.0 and KFH6.0 The thimble is the link between the anti-torsion of the sail and the furler. It is an anodized aluminum part that adapts perfectly to the forks of our furlers.

Aluminum thimble for KF6.0, KTS6.0 and KFH6.0 The thimble is the link between the anti-torsion of the sail and the furler. It is an anodized aluminum part that adapts perfectly to the forks of our furlers.

ALUMINUM THIMBLE FOR KF8.0...

Aluminum thimble for KF8.0, KTS8.0 and KFH8.0 The thimble is the link between the anti-torsion of the sail and the furler. It is an anodized aluminum part that adapts perfectly to the forks of our furlers.

Aluminum thimble for KF8.0, KTS8.0 and KFH8.0 The thimble is the link between the anti-torsion of the sail and the furler. It is an anodized aluminum part that adapts perfectly to the forks of our furlers.

TURNBUCKLE COVER FOR KRS30...

The turnbuckle tube cover is made of an aluminum profile with a larger diameter than the standard profile. When the turnbuckle is installed, the cover is mounted just above the drum to conceal it and extends outward from the drum. If no turnbuckle is used, the turnbuckle cover is not required.

The turnbuckle tube cover is made of an aluminum profile with a larger diameter than the standard profile. When the turnbuckle is installed, the cover is mounted just above the drum to conceal it and extends outward from the drum. If no turnbuckle is used, the turnbuckle cover is not required.

ANTI TWIST SWIVEL 3.0...

Z-SPARS - TRACK END...

Track end for 25 mm track Material: Aluminum 

Track end for 25 mm track Material: Aluminum 

Z-SPARS - 140 X 45 MM...

Z-SPARS Aluminium cover for the mast ( 140 X 45 mm) 

Z-SPARS Aluminium cover for the mast ( 140 X 45 mm) 

Z-SPARS - HALYARD EXIT...

Stainless steel halyard exit plate (96 x 18mm) and will handle a line up to 9mm in diameter. The cast plate fits in the mast cutout 64 mm high x 13mm wide and fastens with a 5mm rivet.

Stainless steel halyard exit plate (96 x 18mm) and will handle a line up to 9mm in diameter. The cast plate fits in the mast cutout 64 mm high x 13mm wide and fastens with a 5mm rivet.

Z-SPARS - HALYARD EXIT...

Stainless steel halyard exit plate (144 x 32mm) and will handle a line up to 18 mm in diameter. The cast plate fits in the mast cutout 112 mm high x 23mm wide and fastens with 5mm rivet.

Stainless steel halyard exit plate (144 x 32mm) and will handle a line up to 18 mm in diameter. The cast plate fits in the mast cutout 112 mm high x 23mm wide and fastens with 5mm rivet.

Reinforcement SS Z300 500

STAINLESS PIN

Z-SPARS - HALYARD EXIT...

Plastic halyard exit plate, visible when installed, (135 x 30 mm), and will handle a line up to 13 mm in diameter. The cast plate fits in the mast cutout 96mm long x 20mm wide and fastens with a 5 mm rivet.

Plastic halyard exit plate, visible when installed, (135 x 30 mm), and will handle a line up to 13 mm in diameter. The cast plate fits in the mast cutout 96mm long x 20mm wide and fastens with a 5 mm rivet.

Z-SPARS - MEDIUM BOOM VANG...

Vang hold load: 250  kg / 551 lbs Range of vang: 180 mm Compatible with boom: Z362 & Z482 Fork Gap: 13 mm Connecting Pin Size: 10 mm Pin to pin length: 2040 mm Weight: 5,1 kg Boom tang: assembly 3047 Mast tang: assembly 3246 / 3252

Vang hold load: 250  kg / 551 lbs Range of vang: 180 mm Compatible with boom: Z362 & Z482 Fork Gap: 13 mm Connecting Pin Size: 10 mm Pin to pin length: 2040 mm Weight: 5,1 kg Boom tang: assembly 3047 Mast tang: assembly 3246 / 3252

Z-SPARS - MAST BASE BLOCK...

A block with a 45 mm diameter sheave will accommodate lines up to 12 mm in diameter. Includes 8mm stud with nut to fit deck castings with 8mm holes and 13mm wide slots for nuts.block with a 45 mm diameter sheave will accommodate lines up to 12 mm in diameter. Includes 8mm stud with nut to fit...

A block with a 45 mm diameter sheave will accommodate lines up to 12 mm in diameter. Includes 8mm stud with nut to fit deck castings with 8mm holes and 13mm wide slots for nuts.block with a 45 mm diameter sheave will accommodate lines up to 12 mm in diameter. Includes 8mm stud with nut to fit...

Z-SPARS - Block Base 10mm D166

Z-SPARS - MAST BASE BLOCK...

A block with an 80 mm diameter sheave will accommodate lines up to 16 mm in diameter. Includes 10 mm stud with nut to fit deck castings with 10 mm holes and 17 mm wide slots for nuts.

A block with an 80 mm diameter sheave will accommodate lines up to 16 mm in diameter. Includes 10 mm stud with nut to fit deck castings with 10 mm holes and 17 mm wide slots for nuts.

Z-SPARS - MAST BASE SWIVEL...

A block with an 60 mm diameter sheave will accommodate lines up to 14 mm in diameter. Includes 10 mm stud with nut to fit deck castings with 10 mm holes and 17 mm wide slots for nuts.

A block with an 60 mm diameter sheave will accommodate lines up to 14 mm in diameter. Includes 10 mm stud with nut to fit deck castings with 10 mm holes and 17 mm wide slots for nuts.

Z-SPARS - MAST BASE SWIVEL...

A block with an 80 mm diameter sheave will accommodate lines up to 16 mm in diameter. Includes 10 mm stud with nut to fit deck castings with 10 mm holes and 17 mm wide slots for nuts.

A block with an 80 mm diameter sheave will accommodate lines up to 16 mm in diameter. Includes 10 mm stud with nut to fit deck castings with 10 mm holes and 17 mm wide slots for nuts.

Z-SPARS - SHEAVE BOX LARGE,...

Large rope sheave box for the mast, polyester (Ø78.5x17.5 mm)

Large rope sheave box for the mast, polyester (Ø78.5x17.5 mm)

Z-SPARS - BOOM BAIL SLIDER...

Stainless steel articulating boom bail fits in the integral track on the underside of Z160, Z204, and other boom sections with a 20mm wide track. Bail is made from 7mm rod. The formed plate is 2mm thick and measures 80mm long x 20mm wide. Fastens with 5mm rivets.

Stainless steel articulating boom bail fits in the integral track on the underside of Z160, Z204, and other boom sections with a 20mm wide track. Bail is made from 7mm rod. The formed plate is 2mm thick and measures 80mm long x 20mm wide. Fastens with 5mm rivets.

Z-SPARS - BOOM BAIL SLIDER...

Stainless steel articulating boom bail fits in the integral track on the underside of Z360-Z480, and other boom sections with a 30mm wide track. Bail is made from 10 mm rod. The formed plate is 2,5 mm thick and measures 120 mm long x 30 mm wide. Fastens with 5mm rivets.

Stainless steel articulating boom bail fits in the integral track on the underside of Z360-Z480, and other boom sections with a 30mm wide track. Bail is made from 10 mm rod. The formed plate is 2,5 mm thick and measures 120 mm long x 30 mm wide. Fastens with 5mm rivets.

Z-SPARS - BOOM CAR BALL...

Z-SPARS Small size car for Boom, for 25mm rail (compatible with Z160/204/360 booms)

Z-SPARS Small size car for Boom, for 25mm rail (compatible with Z160/204/360 booms)

Z-SPARS - BOOM OUTHAUL CAR...

Boom outhaul car for tensioning the foot of the mainsail (suitable for Z362-Z690 booms) Large size / Rod bearings / Suitable for 25 mm track

Boom outhaul car for tensioning the foot of the mainsail (suitable for Z362-Z690 booms) Large size / Rod bearings / Suitable for 25 mm track

Z-SPARS - MAINSAIL LUFF FEEDER

Gray plastic mainsail feeder entrance is used on all Z-Spars mast sections that use a boltrope luff. Unit is 80mm high x maximum 45mm wide and fastens with 3/16" rivets or screws. Fasteners are on 65mm vertical x 30 mm (lower) x 23mm (upper) hole centers.

Gray plastic mainsail feeder entrance is used on all Z-Spars mast sections that use a boltrope luff. Unit is 80mm high x maximum 45mm wide and fastens with 3/16" rivets or screws. Fasteners are on 65mm vertical x 30 mm (lower) x 23mm (upper) hole centers.

Spreader Tip Dinghy Assembly

Z-SPARS - SPREADER TIP END...

New-style gray plastic spreader tip for use with tapered Z95 spreader. Includes C-Clamp with screw, to clamp shroud to the spreader tip. When installed, the clamp must be tight and positioned carefully on the shroud. The tip is a maximum 62 mm long x 29 mm wide.

New-style gray plastic spreader tip for use with tapered Z95 spreader. Includes C-Clamp with screw, to clamp shroud to the spreader tip. When installed, the clamp must be tight and positioned carefully on the shroud. The tip is a maximum 62 mm long x 29 mm wide.

Z-SPARS - SPREADER TIP END...

Gray plastic spreader tip for use with the tapered Z240 spreader. Includes 6mm L-bolt with locknut, to clamp shroud to the spreader tip prior to installation in the spreader tube. When used with hinged spreader bases, clamp must be tight and positioned carefully on the shroud. The tip is a...

Gray plastic spreader tip for use with the tapered Z240 spreader. Includes 6mm L-bolt with locknut, to clamp shroud to the spreader tip prior to installation in the spreader tube. When used with hinged spreader bases, clamp must be tight and positioned carefully on the shroud. The tip is a...

Z-SPARS - BOOM TRACK END

Track end for 25 mm track Material: Composite

Track end for 25 mm track Material: Composite

Z-SPARS - END FOR SPINNAKER...

Z-SPARS - SPINNAKER POLE...

Spinnaker pole end (diam.80 mm)

Spinnaker pole end (diam.80 mm)

Z-SPARS - SPINNAKER POLE...

Spinnaker pole end (diam.100 mm)

Spinnaker pole end (diam.100 mm)

Z-SPARS - HALYARD SWIVEL...

The halyard swivel D-shackle assembly, designed for secure halyard connections and smooth sail handling. Manufactured from high-quality marine-grade stainless steel, this shackle offers excellent corrosion resistance and long-term durability, even in harsh saltwater environments. 

The halyard swivel D-shackle assembly, designed for secure halyard connections and smooth sail handling. Manufactured from high-quality marine-grade stainless steel, this shackle offers excellent corrosion resistance and long-term durability, even in harsh saltwater environments. 

Z-SPARS -D-SHACKLE FOR THE...

This Shackle is a high-quality marine-grade shackle designed to provide secure and reliable tack connections in sailing applications. Made from corrosion-resistant stainless steel, this shackle ensures durability and longevity, even in harsh saltwater environments.

This Shackle is a high-quality marine-grade shackle designed to provide secure and reliable tack connections in sailing applications. Made from corrosion-resistant stainless steel, this shackle ensures durability and longevity, even in harsh saltwater environments.

Z-SPARS - SPINNAKER POLE...

Spinnaker pole conical end (Ø 80 mm)

Spinnaker pole conical end (Ø 80 mm)

Z-SPARS - SPINNAKER POLE...

Spinnaker pole conical end (Ø 100 mm)

Spinnaker pole conical end (Ø 100 mm)

Intermediate Car For 32mm...

Z-SPARS - INTERMEDIATE CAR...

Ball bearing intermediate car for use with masts using Z-Spar RCB 25 mm track. The car incorporates delrin spool for attachment to the sail with webbing. Car rides on torlon ball bearings to provide high strength and low friction at a minimum weight. Short cars allow reduced stack height. The car...

Ball bearing intermediate car for use with masts using Z-Spar RCB 25 mm track. The car incorporates delrin spool for attachment to the sail with webbing. Car rides on torlon ball bearings to provide high strength and low friction at a minimum weight. Short cars allow reduced stack height. The car...